Moisture Control

ARDEX MC™ RAPID


Description:

​The ARDEX MC™ RAPID MOISTURE CONTROL SYSTEM is a one-coat, 100% solids epoxy moisture management system formulated to suppress excessive moisture vapor emissions in new or existing concrete prior to installing an ARDEX underlayment with flooring. It is especially suited to treat areas of new concrete in critical installations, such as health care and institutional applications where the construction schedule does not allow adequate drying of the concrete. ARDEX MC RAPID is also recommended over existing concrete where the level of moisture emissions from the slab exceeds the maximum allowed by the manufacturer of the finished floor covering.


ARDEX K 301™


Description:

​ARDEX K 301™ is a self-leveling Portland cement-based topping and underlayment for fast-track resurfacing and smoothing for exterior and interior applications over concrete, porous tile and certain non-porous surfaces when properly prepared – on, above or below grade. ARDEX K 301 can be sealed to create a concrete wear surface for commercial, light industrial and residential applications, including storage rooms, workshops, parking garages, parking decks, driveways, patios and plazas. It can also be used as an underlayment for finish flooring, as well as on permanently wet areas and under moisture remediation systems such as the ARDEX Moisture Control Systems. Installs from 4” to w” in one application, and up to 2” with the addition of appropriate aggregate. Pourable or pumpable when mixed with water. Seeks its own level and produces a smooth, flat, hard surface. Hardens quickly and dries fast without shrinking, cracking or spalling. ​​


ARDEX VR 98™


Description:

ARDEX VR 98™ is a ready-to-use, one-component, water-based, two-coat system formulated to suppress residual moisture in concrete with RH readings up to 98%. ARDEX underlayments may be installed over the second coat in as little as 2 hours without priming. ARDEX VR 98 comes in a ready-to-use, resealable container. It is pigmented blue to help indicate uniform coverage for ease of application.


ARDEX MRP™


Description:

​ARDEX MRP™ is a trowel-grade, cementitious patching and smoothing compound for filling and repairing heavily profiled indoor concrete on all grade levels prior to the installation of ARDEX Moisture Control Systems. Engineered with Portland cement and select high-performance polymers, ARDEX MRP bonds readily to concrete surfaces. It produces a surface finish without having to re-profile the surface of the patch after it is installed.


ARDEX ARDIFIX™


Description:

​ARDEX ARDIFIX™ is a two-part polyurethane repair compound for cracks, control joints, spalls and pop-outs on interior or exterior applications. It is ideally suited to seal off cracks and saw-cuts prior to the installation of ARDEX MC™ Moisture Control Systems, Underlayments and Toppings. ARDEX ArdiFix is ultra fast setting allowing the installation to proceed within minutes of application. ARDEX ArdiFix is 100% solids for no shrinkage and cures to a rigid hardness. It also has a wide service temperature range of 0°F to 110°F (-17 to 43°C), making it suitable for applications from freezers to warehouses.


Enhance™


Description:

ENHANCE is a unique one-part next generation bond promoter, surface texturizer and encapsulator that is alkali and water-resistant. It is designed for use over Sahara Moisture Barrier and other difficult to bond to substrates such as OSB underlayments, well-bonded residue from cutback adhesives, multi-purpose adhesives, and pressure sensitive adhesives. It has long term water and humidity resistance, as well as good solvent, chemical and corrosion resistance.


SAHARA™


Description:

Sahara™ was developed to tackle the most challenging moisture mitigation issues by offering premium protection in a 1-part, 1-coat system. Sahara™ forms a clear, water repelling moisture vapor barrier that can handle any situation without needing to test moisture levels, making it one of the most aggressive moisture mitigation products on the market. Designed for use with Taylor ENHANCE.


ZEPHYR™


Description:

Moisture mitigation doesn’t always have to come at a price. Zephyr™ gives protection up to 95% (RH) at a pricepoint that is much more attractive than competing systems. With quick and easy application, Zephyr™ is sure to be a favorite for customers with common moisture issues.